WORKINGMAN’S 8004 T/O/P FRONT PANEL FEATURES • Steel chassis enclosed in custom carpeted rack case (with stack-lock corners and side strap handle) • Discrete solid-state front end • XLR Mute Switch • Hi and Low Sensitivity 1/4" Inputs • Gain control with LED peak clipping indicator • Shape control • Bass control • Lo-Mid control • Mid control • Hi-Mid control • Treble control • Effects Blend control • Master Volume control • Stereo Headphones Jack • Speaker On/Off switch • Illuminated Neon Power On/Off switch WORKINGMAN’S 8004 T/O/P REAR PANEL FEATURES • Balanced (XLR) Output jack • Ground Lift Switch for XLR Output jack • Line/Direct Switch for XLR Output jack • Tuner Out jack • Side-Chain Effects Loop (Effects Send and Effects Return 1/4" jacks) • Unbalanced Line Out jack (pre-master) • Preamp Out jack (post-master) • Power Amp In jack • Cooling Fan On/Off switch • Two 1/4" Speaker Output jacks • Two Speakon Output jacks • Speaker Fuse (10 Amp Fast-Blo) • Line Fuse • A/C Receptacle
 
ELECTRICAL SPECIFICATIONS Note: All measurements were taken with a line voltage of 120VAC. All voltages and watts are “RMS.” All measurements are taken with tone controls set flat, Shape control at minimum. Power Ratings (minimum): 750 Watts @ 4 ohms 450 Watts @ 8 ohms Power Bandwidth (frequency response): (@ 850 watts RMS) -3dB @ 20 Hz and 40 kHz Dimensions: 23 1/4" W x 7 1/2" H x 13 1/2" D Weight: 37 lbs.
 
BIG BEN SPECIFICATIONS Power Handling: 400 watts RMS Impedance: 8 Ohms Frequency Response and SPL: 100 dB SPL @ 2W1M (–6dB @ 25 Hz and 3 kHz) Speaker Complement: (1) 18" Woofer Spring Loaded Rubber Grip Handles, Rear Circular Ports Dimensions: 23"W x 30.5"H x 18.5"D Weight: 73 lbs. DESCRIPTION Big Ben is an extremely fast, 1x18 subwoofer. It can be used as a stand-alone speaker enclosure, as part of a bi-amp system, or as the low end component for any large, multi-speaker bass rig. It’s a must-have for any true bottom dweller. CONNECTION AND OPERATION Big Ben can be connected to any musical instrument amplifier that is capable of driving an 8 ohm load. To connect your amplifier to Big Ben, run a high quality speaker cable (18 gauge or heavier) from your amplifier’s speaker output to one of the designated speaker inputs (Speakon on 1/4”) on Big Ben’s input panel. POWER HANDLING The power output rating for any amplifier connected to Big Ben should not exceed the enclosure’s 400 watt RMS power handling capacity. Please be aware that exceeding Big Ben’s power handling capacity can void the SWR warranty if any damage occurs to the 18" woofer due to overpowering. FULL RANGE INPUT AND OUTPUT JACKS Big Ben features four, full range input/output jacks (two standard 1/4" and two Speakon) wired in parallel. If you are running two speaker enclosures in parallel, connect the speaker cable from your amplifier to either jack labeled “IN,” and a second speaker cable from either jack labeled “OUT” to the input of the second speaker enclosure.
 
HENRY THE 8x8 SPECIFICATIONS Description: 8x8 + Tweeter Speaker Enclosure Power Handling: 480 watts RMS Impedance: 4 ohms Frequency Response & SPL: 96 dB SPL @ 1W1M (–6 db @ 35 Hz and 18 Khz) Speaker Complement: (8) custom 8" SWR drivers, (1) Le-Son piezo tweeter Heavy-Duty Casters, Spring Loaded Rubber Grip Handles, 2 Front Tube Ports, Top Handle and Tilt Back Design for easy transportation. Dimensions: 23"W x 36.5"H x 18.5"D Weight: 100 lbs. CONNECTION AND OPERATION Henry The 8x8 can be connected to any musical instrument amplifier capable of driving a 4 ohm load. To connect your amplifier to Henry The 8X8, run a high quality speaker cable (18 gauge or heavier) from your amplifier’s speaker output to one of the designated speaker inputs (Speakon or 1/4") on Henry The 8x8’s input panel. POWER HANDLING The power output rating for any amplifier connected to Henry The 8X8 should not exceed the enclosure’s 480 watt RMS power handling capacity. Please be aware that exceeding Henry The 8X8’s power handling capacity can void the SWR warranty if any damage occurs to your loudspeakers due to overpowering. FULL RANGE INPUT AND OUTPUT JACKS Henry The 8X8 features four, full range input/output jacks (two standard 1/4" and two Speakon) wired in parallel. If you are running two speaker enclosures in parallel, connect the speaker cable from your amplifier to either jack labeled “IN,” and a second speaker cable from either jack labeled “OUT” to the input of the second speaker enclosure. TWEETER ATTENUATOR CONTROL The large dial found on the input panel of the cabinet is the Tweeter Attenuator. This control is used to adjust the level of high frequency signal present at the tweeter. A normal setting for this control is straight up or “twelve o’clock.” Turning the dial fully counter-clockwise removes the tweeter from the circuit. As you turn the dial clockwise from this position, the high frequency content is increased. INTERNAL CROSSOVER Henry The 8X8’s internal (passive) crossover divides the incoming signal into two frequency bands. The crossover point is 5 kHz (frequencies above 5 kHz are sent to the tweeter, frequencies below 5 kHz are sent to the 8" speakers).